New product
Teamac Chlorvar is achlorinated rubber finish resistant to salt water, a wide range of chemicals and acids. For Interior or exterior use.
Teamac Chlorvar is used as a gloss finish to provide protection in moderate to severe corrosive atmospheres. It is suitable for use on swimming pool surfaces, milking parlours, piping and structural steel in chemicals works, laundries and marine applications.
Teamac Chlorvar is a modified chlorinated rubber finish coat for use over Metaclor Underwater Primer. Resistant to salt water, a wide range of chemicals and acids. Interior or exterior use.
Teamac Chlorvar is used as a gloss finish to provide protection in moderate to severe corrosive atmospheres.
It is suitable for use on concrete and cement swimming pool surfaces, milking parlours, piping and structural steel in chemicals works, laundries and marine applications.
Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material.
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.
Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas.
Mild Steel
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.
Phosphate Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat
Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.
Application Conditions
Relative humidity should not exceed 80%.
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.
Recommended Finish Coats
Overcoat with itself only
Recommended Thinners
Chlorvar Thinners
Coverage Rates
Recommended Film weight:Minimum WFT 75µm
Theoretical coverage rate: 14m² per litre
Application Methods
Teamac Chlorvar can be applied by the following methods.
Airless Spray: Yes
Brush: Yes
Roller: Yes
Application Guidance
Airless Spray
Output fluid pressure at tip 1800-2000 psi,
Tip Size 17-21 thou
Thinning with Chlorvar Thinner (Note thinning will reduce the film weight)
Brush / Roller
Thin up to 5% to achieve a smooth film flow.
Please note: application by brush and roller will result in a reduced film thickness.
Drying times at a WFT at 85µm and 20ºC
Dust Dry: 2h
Hard Dry: 24 hours, Full Hardness 7 to 14 days
Cleaning Tools and Equipment
Clean equipment with Chlorvar Thinner after use
% Volume Solids : 23-25%
Safe use.
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.
For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet.
This is our Industrial coatings website. We also have a range of sister sites, each dedicated to a specific sector.
SHOP BY CATEGORY
SHOP BY MANUFACTURER
We are able to supply our primers and topcoats in a vast array of colours. In addition, we are able to provide very accurate equivalent matches to the paint ranges of the well recognized trade professional and retail designer colour collections. If this were not enough, we are also able to scan and provide close matches to materials such as plastic, glass, printed colour and textiles.
01793 511537
sales@hspindustrial.co.uk
Holman Specialist Paints Ltd, 1 Central Trading Estate
Signal Way, Swindon, SN3 1PD