Axalta ViterBlast EV110 Two Pack Epoxy Zinc Phosphate Blast Primer

New product

A two pack epoxy zinc phosphate holding primer for the temporary protection of blast cleaned steelwork.
Fast drying to ensure minimal stoppage for continual blasting operations
Lloyds Register welding approvals

Where temporary protection is required prior to fabrication
Suitable for marine plate and structural steel
Application by automatic spray, airless spray and conventional spray

More details

£83.66

- +

Brand: Axalta

 
Product Info

A two pack epoxy zinc phosphate holding primer for the temporary protection of blast cleaned steelwork.

Fast drying to ensure minimal stoppage for continual blasting operations
Lloyds Register welding approvals
Enables welding and fabrication when applied at the recommended dry film thickness
Can be overcoated with most generic groups (excluding zinc rich)
Where temporary protection is required prior to fabrication
Suitable for marine plate and structural steel
Application by automatic spray, airless spray and conventional spray

Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material. 
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat

Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions
Relative humidity should not exceed 80%. 
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats
Overcoat with Two Pack Epoxy Primers

Recommended Thinners 
Do not thin

Coverage Rates
Recommended Film weight: WFT 62µm 
Theoretical coverage rate: 16.0m² per litre

Application Methods
ViterBlast EV110 can be applied by the following methods.

Airless Spray: Yes
Conventional Spray: Yes
Brush: Yes 
Roller: Yes

Mix Ratio: 3 Part base :1 Part hardener

Pot life: 12 hours at 23ºC

Application Guidance 
Airless Spray
Output fluid pressure at tip 1500-2500psi, 
Tip Size 15-23 thou (0.38-0.58 mm) 

Brush / Roller 
Recommended for small areas and touch up. Thin as appropriate to achieve a smooth film flow.

Please note: application by brush and roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work as it dries very quickly

Drying times at a WFT at 62µm and 23ºC 
Dust Dry: 3 minutes 
Recoatable:  8h
Hard Dry: 5 minutes  

Cleaning Tools and Equipment
Clean equipment with 950 Thinner after use

% Volume Solids :32%
VOC content : 570-610g / litre

Safe use
This product is formulated for professional use. 
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet.

 
Download

Accessories

30 other products in the same category:

Menu

Top
Compare 0