New product
A hard-wearing Plant Enamel coating with a gloss finish.
Excellent adhesion to new and previously painted equipment and can be applied by brush, roller or spray.
It provides high resistance to spillages of oil, petrol, detergents and dilute aqueous chemical solutions.
Available in any colour.
Teamac Metalcote is a hard-wearing protective Plant Enamel. It has excellent adhesion properties to new and previously painted equipment and can be applied by brush, roller or spray.
It provides high resistance to spillages of lubricating and mineral oil, petrol, detergents and dilute aqueous chemical solutions.
Machinery can be back in service between 36-48 hours after coating.
Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material.
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.
Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas.
Mild Steel
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.
Phosphate Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat
Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade.
The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.
Application Conditions
Relative humidity should not exceed 80%.
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.
Recommended Finish Coats
Overcoat with itself only
Recommended Thinners
Thinners 14
Coverage Rates
Recommended Film weight:Minimum WFT 85µm
Theoretical coverage rate: 12m² per litre
Application Methods
Teamac Metalcote Machinery Enamel can be applied by the following methods.
Airless Spray: Yes
Brush: Yes
Roller: Yes
Application Guidance
Airless Spray
Output fluid pressure at tip 1800-2000psi,
Tip Size 11thou (0.33-0.48 mm)
Thinning with Thinner 14 (Note thinning will reduce the film weight)
Brush / Roller
Thin up to 10% to achieve a smooth film flow.
Please note: application by brush and roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work
Drying times at a WFT at 85µm and 20ºC
Dust Dry: 2-3h
Hard Dry: 8 hours, Full Hardness 3 to 5 days
Cleaning Tools and Equipment
Clean equipment with Thinner 14 or White Spirit Thinner after use
% Volume Solids : 35%
Safe use.
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.
For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet.
This is our Industrial coatings website. We also have a range of sister sites, each dedicated to a specific sector.
SHOP BY CATEGORY
SHOP BY MANUFACTURER
We are able to supply our primers and topcoats in a vast array of colours. In addition, we are able to provide very accurate equivalent matches to the paint ranges of the well recognized trade professional and retail designer colour collections. If this were not enough, we are also able to scan and provide close matches to materials such as plastic, glass, printed colour and textiles.
01793 511537
sales@hspindustrial.co.uk
Holman Specialist Paints Ltd, 1 Central Trading Estate
Signal Way, Swindon, SN3 1PD