New

Protega Viterthane PLV Two Pack Recoatable Gloss Finish

New product

A two pack polyurethane recoatable gloss finish that is UK Network Rail approved

Excellent colour retention and indefinitely overcoatable

Excellent chemical resistance and low temperature curing

Use as a finish coat over high performance systems where longer term cosmetic properties and chemical resistance are required

Available in any colour

More details

£66.20

- +

Brand: Axalta

 
Product Info

A two pack polyurethane recoatable gloss finish for steelwork that is UK Network Rail approved.

Excellent colour retention and indefinitely overcoatable

Excellent chemical resistance and low temperature curing

Use as a finish coat over high performance systems where longer term cosmetic properties and chemical resistance are required

Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material. 
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat

Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions
Relative humidity should not exceed 80%. 
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats
Overcoat with itself only

Recommended Thinners 
1737 Thinners

Coverage Rates
Recommended Film weight:Minimum WFT 57µm Maximum 113µm
Theoretical coverage rate: 8.8-17.7m² per litre

Application Methods
Viterthane PLV Gloss can be applied by the following methods.

Airless Spray: Yes
Conventional Spray: Yes
Brush: Yes 
Roller: Yes

Mix Ratio: 5 Parts base :1 Part hardener

Pot life: 4 hours at 23ºC

Application Guidance 
Airless Spray
Output fluid pressure at tip 2200-2500psi, 
Tip Size 13-17 thou (0.33-0.43 mm) 
Thinning with 1737 (Note thinning will reduce the film weight)

Brush / Roller 
Recommended for small areas and touch up. Thin as appropriate to achieve a smooth film flow.

Please note: application by brush and roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT at 75µm and 23ºC 
Dust Dry: 1h 
Recoatable:  12h
Hard Dry: 3h 

Cleaning Tools and Equipment
Clean equipment with 1737 Thinner after use

% Volume Solids : 55%
VOC content : 411-450g / litre

Safe use
This product is formulated for professional use. 
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet.

 
Download

Viterthane PLV

Product Datasheet

Download PDF

Accessories

30 other products in the same category:

Menu

Top
Compare 0