Tikkurila Temadur Clear, Two Pack Polyurethane

New product

A two pack, glossy polyurethane varnish providing a durable, non chalking topcoat with good gloss retention and an easy to clean surface. Can be used as a topcoat over polyurethane paint systems. Recommended for painting storage tanks exteriors,steel buildings and other steelwork.

Clear Gloss Finish

Pack size 6 litre

More details

£98.50

- +

 
Product Info

A two pack, glossy polyurethane varnish providing a durable, non chalking topcoat with good gloss retention and an easy to clean surface. Can be used as a topcoat over polyurethane paint systems.

Gloss finish

Pack size 6 litre

Two pack, glossy polyurethane varnish, hardener aliphatic isocyanate.

Excellent weathering and abrasion resistance

Used as a topcoat on polyurethane paint systems

A durable, non-chalking topcoat with good gloss retention and easy to clean surface.

Suitable for coating of copper, brass, aluminium and zinc surfaces

The product has MED (Marine Equipment Directive) certificate no VTTC-11095-15-14 and is  accepted for painting surfaces inside the ships

For industrial use only according to Directive 1999/13/EC

Recommended for painting storage tanks exteriors,steel buildings and other steelwork

Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material. 
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat

Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions
Relative humidity should not exceed 80%. 
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats
Overcoat with itself 

Recommended Thinners 
1048 or 1067 Thinners

Coverage Rates
Recommended Film weight:Minimum WFT 95µm 
Theoretical coverage rate: 10.7m² per litre

Application Methods
Tikkurila Temadur Clear can be applied by the following methods.

Airless Spray: Yes
Conventional Spray: Yes
Brush: Yes 
Roller: Yes

Mix Ratio: 3 Parts base :1 Part hardener

Pot life: 2-4 hours at 23ºC depending on viscosity

Application Guidance 
Airless Spray
Output fluid pressure at tip 1700 - 2300 psi, 
Tip Size 13-19 thou 
Thinning with 1048 or 1067 (Note thinning will reduce the film weight)

Brush / Roller 
Recommended for small areas and touch up. Thin as appropriate to achieve a smooth film flow.

Please note: application by brush and roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT at 95µm and 23ºC 
Dust Dry: 20 min 
Recoatable: 30 min - 72h

Cleaning Tools and Equipment
Clean equipment with 1048 or 1067 Thinner after use

% Volume Solids : 42-44%
VOC content : 510-600g / litre

Safe use
This product is formulated for professional use. 
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet.

30 other products in the same category:

Menu

Top
Compare 0