Top sellers

Quick Drying Enamel

New product

A High Performance, Quick Drying Low Odour Synthetic Enamel in any Colour Touch dry in 30 minutes and is available in a Matt, Satin or Gloss finish.

More details

We can tint this product to your exact specification from any colour chart or sample. Enter your chosen colour in the box below and click CONFIRM COLOUR before adding the product to your basket. Need help? Call us on 01793 511537

ENTER COLOUR CHOICE:

loader

£48.95

- +

Brand: Ace

 
Product Info

An easy to use quick drying finish that is available in any colour. Touch dry in 30 minutes is available in matt , satin or gloss finish. 

Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material. 
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer Coat

Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions
Relative humidity should not exceed 80%. 
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats
Overcoat with itself only

Recommended Thinners 
Solvent X Thinners or SNAP Solvent for extended wet edge times

Coverage Rates
Recommended Film weight:Minimum WFT 200µm 
Theoretical coverage rate: 6.0m² per litre

Application Methods
ACE 'ET' Quick Drying Enamel can be applied by the following methods.

Airless Spray: no
Conventional Spray: Yes
Brush: Yes 
Roller: Yes

Application Guidance 
conventional Spray - Thin up to 20%

Brush / Roller 
Recommended for small areas and touch up. Thin as appropriate to achieve a smooth film flow.

Please note: application by brush and roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT at 200µm and 23ºC 
Dust Dry: 30 min
Recoatable: Next Day
 

Cleaning Tools and Equipment
Clean equipment with  Solvent X Thinner after use

% Volume Solids : 40%

Safe use
This product is formulated for professional use. 
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet.

 
Download
 
Product customization

We can tint this product to your exact specification from any colour chart or sample. If you know the reference please enter the code in the field below, click SAVE and add the product to your basket. We also have ideas to set the ball rolling in our Colour section where we have added a number of widely used colour ranges. Need help? Call us on 01793 511537

Enter your COLOUR REFERENCE in the box below:

loader

* required fields

30 other products in the same category:

Recently Viewed

Menu

Top
Compare 0