New

Axalta ViterLac Containergard HS

New product

Protega ViterLac Containergard (HS) is a a high build, fast drying one-coat system with a Sheen finish which helps disguise typical dents and welds. 

A high content of zinc phosphate anti-corrosive pigment gives high levels of protection in aggressive environments.

Available in any colour including  Agricultural, RAL and BS collections

More details

£143.75

- +

Brand: Axalta

 
Product Info

Protega ViterLac Containergard (HS) is a a high build, fast drying one-coat system with a Sheen finish which helps disguise typical dents and welds. 

Specially formulated for the transport container market and for Commercial Vehicle Chassis protection.

A high content of zinc phosphate anti-corrosive pigment gives high levels of protection in aggressive environments.

Tested to BS476 Part 7 (Surface Spread of Flame) - Class 1 and BS476 Part 6 (Fire Propagation) - Class 0. Resistant to splashes of diesel, petrol and hydraulic fluid. 

Ideal for use on dry cargo transport containers, ISO tank containers, anti-vandal accommodation units, waste containers and other industrial steel fabrications.  

Preparation
Surfaces to be coated must be clean, dry and free from any material such as oil, grease, salts and dirt that might affect adhesion.
Remove loose flaking or friable material. 
Where necessary, remove weld spatter and grind smooth all rough,sharp edges and weld seams.

Galvanised steel
Thoroughly degrease with Cleaner Degreaser (Product Reference H30 or ND14) and lightly abrade any very shiny areas. 

Mild Steel 
Degrease with a Cleaner Degreaser (Product Reference H30 or ND14) and either manually abrade or blast clean to Sa2½ (ISO 8501-1:2007)
If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.

Phosphate Steel 
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade prior to application of the Primer/Finish Coat

Stainless Steel
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

Aluminium and Alloys
Degrease with Cleaner Degreaser (Product Reference H30 or ND14) and manually abrade. 

The temperature of the ambient air, surface or paint should not fall below 5ºC during application or drying.

Application Conditions
Relative humidity should not exceed 80%. 
The surface temperature of the steel should remain at least 3ºC above the dew point.
Cold damp conditions will impair drying times and the final finish.

Recommended Finish Coats
Overcoat with itself only

Recommended Thinners 
1006 Thinners

Coverage Rates
Recommended Film weight:Minimum WFT 125µm Maximum 208µm
Theoretical coverage rate: 4.8-8m² per litre

Application Methods
ViterLac Containergard (HS) can be applied by the following methods.

Airless Spray: Yes
Conventional Spray: No
Brush: Yes 
Roller: no

Application Guidance 
Airless Spray
Output fluid pressure at tip 2500psi, 
Tip Size 15-17 thou   
Thinning with 1006 (Note thinning will reduce the film weight) 

Brush
Recommended for small areas and touch up. Thin as appropriate to achieve a smooth film flow.

Please note: application by brush will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work

Drying times at a WFT at 125µm and 23ºC 
Dust Dry: 30 min
Hard Dry: 3h 

Cleaning Tools and Equipment
Clean equipment with 1006 Thinner after use

% Volume Solids : 65%
VOC content : 320-360g / litre

Safe use
This product is formulated for professional use. 
Please ensure suitable and appropriate personal protective equipment is worn during handling and application.

For more detail please consult the Product Datasheet.
Please contact us for the Health and Safety Datasheet

 
Download

Accessories

14 other products in the same category:

Menu

Top
Compare 0