Protega ViterShield 178 Maximize

Protega ViterShield 178

ViterShield 178 HS Epoxy Primer/Finish

A two pack epoxy, high solids, zinc phosphate primer or primer/finish for steelwork.

High performance, low VOC coating to help meet SED requirements.

Specially formulated for high build airless spray application with rapid drying and curing properties

Good resistance to undercutting from damaged areas.

More details

£ 100.00

ViterShield 178 HS Epoxy Primer/Finish

A two pack epoxy, high solids, zinc phosphate primer or primer/finish for steelwork. High performance, low VOC coating to help meet SED requirements.

Specially formulated for high build airless spray application with rapid drying and curing properties

Good resistance to undercutting from damaged areas.

  

Surface Preparation  

Blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50-75 microns.  

All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams.  

Mixing Mix only in the proportions stated, mixing each component individually then together using a mechanical agitator. Agitate periodically during use to ensure product remains homogeneous.

Thinner 1031 Thinner

Equipment Cleaner 950 Thinner

Application Conditions

Only apply in conditions of good ventilation which must be maintained during drying and curing. Do not apply when rain, mist, sleet or snow are imminent. During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3oC above the dew point. Only apply this product when the above conditions can be maintained throughout the critical application and drying/curing process. Paint temperature should ideally be at a minimum of 15ºC.

Application Methods  

Airless Spray, Yes

Conventional Spray, Yes

Brush, Yes

Roller, Yes

Airless Spray:

Output fluid pressure at tip 2200 psi, Tip Size: 13 thou (0.33mm) for dft’s 75-125um; 15-17 thou (0.38-0.43mm) for 125-280um. Thinning of the coating will reduce the build qualities  

Application by brush/roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work.   

 Overcoating

May be overcoated with itself or other products from the ViterShield, ViterSeal or ViterThane range If overcoating with ViterThane PLV or PLS, allow a minimum of 12 hours at 23oC when the primer has been applied to 100 microns dft.

Allow longer drying and overcoating times at higher dft’s and lower temperatures.

The compatibility of overcoating should be confirmed prior to application High Film Builds.

Certain configurations of steelwork may mean that the primer will have to be applied in more than one coat to achieve the higher film thicknesses.

Other   

Whilst this product will display a matt finish at a dry film thickness of 75 microns, application to a dry film thickness above 125 microns will provide a low sheen finish, the degree of which may vary   

Do not apply or cure below 5oC, temperatures above 10oC recommended.  

Like all epoxy coatings, this product will chalk on prolonged exterior exposure, the degree of which is subject to atmospheric conditions

Health & Safety

Containers are provided with safety labels which should be observed. Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets. A Safety Data Sheet for this product is available on request.

 

No customer comments for the moment.

Write your review

Protega ViterShield 178

Protega ViterShield 178

ViterShield 178 HS Epoxy Primer/Finish

A two pack epoxy, high solids, zinc phosphate primer or primer/finish for steelwork.

High performance, low VOC coating to help meet SED requirements.

Specially formulated for high build airless spray application with rapid drying and curing properties

Good resistance to undercutting from damaged areas.

Write your review

Related products

RustOleum Metal Cladding Primer RustOleum Metal Cladding...
Don’t replace old and weathered cladding, Renovate with the...
Teamac Marine Undercoat Teamac Marine Undercoat
Teamac Marine Undercoat is an interior and exterior, oil based...
Teamac Marine Gloss Teamac Marine Gloss
Teamac Marine Gloss is a high quality, modified alkyd marine...
Teamac Tropical Killa Teamac Tropical Killa
Teamac Protector Antifouling contains cuprous oxide to give...
Teamac Protector Antifoul II Teamac Protector Antifoul II
Teamac Protector Antifouling contains cuprous oxide to give...
Teamac Antifouling D Teamac Antifouling D
Teamac Antifouling ‘D’ is a  physically ablative product and...
Teamac Antifouling A Teamac Antifouling A
Teamac "A" Antifouling is a premium physically ablative...
Teamac Boot Topping Teamac Boot Topping
5A high quality, hard wearing boot-topping paint. Used to...
Teamac Anti-Slip Suregrip Deck paint Teamac Anti-Slip Suregrip...
Teamac Suregrip provides an anti-slip finish for wood, grp and...
Teamac Bilge Paint Teamac Bilge Paint
Teamac Bilge Paint provides protection for the inside surfaces...
RustOleum Combicolor RustOleum Combicolor
A high performance, one coat interior and exterior maintenance...
Rustoleum Pegakote Rustoleum Pegakote
A waterborne, high performance satin gloss floor coating with...
RustOleum Flexible  Epoxy B95 RustOleum Flexible Epoxy B95
 Outstanding corrosion protection in heavy industrial or...
SteelSeal Metal Cladding Maintenance Paint SteelSeal Metal Cladding...
SteelSeal Metal Cladding Maintenace Paint  Akzo Nobel's...
SteelSeal Metal Cladding Maintenance Primer SteelSeal Metal Cladding...
SteelSeal Metal Cladding Maintenace Primer Akzo Nobel's...
Protega ViterPrime 035 High Build Zinc Phosphate Primer/Finish New Protega ViterPrime 035 High...
Single Pack, Quick Drying High Build Zinc Phosphate Primer for...
Protega ViterPrime 016 Single Pack Zinc Phosphate Primer New Protega ViterPrime 016...
 An easy to use alkyd zinc phosphate anticorrosive primer, for...
Protega ViterLac 305 Vinyl Acrylic Anti-Corrosive Primer/finish New Protega ViterLac 305 Vinyl...
A high performance single pack Vinyl Acrylic Anti-Corrosive...
Protega ViterLac OCF Anti-corrosive Gloss Primer/Finish New Protega ViterLac OCF...
A single pack one coat Anti-Corrosive One Coat Full Gloss...
Protega ViterLac 046 Anti-corrosive Semi-Gloss Primer/Finish New Protega ViterLac 046...
A fast drying one coat, semi-gloss, anticorrosive...
Protega ViterLac C12  Anti-Corrosive Primer/Finish for Containers New Protega ViterLac C12...
 A single pack, phenolic-modified alkyd primer/finish,...
Protega ViterLac Containergard HS New Protega ViterLac...
A single pack Modified Anti-Corrosive One Coat Full Primer /...
Protega Prime VRP Compliant Primer for Vehicle Refinishing New Protega Prime VRP Compliant...
A single pack, fast drying alkyd primer specially designed for...
ProtegaPrime QD Matt Primer New ProtegaPrime QD Matt Primer
An single pack Modified Anti-Corrosive Matt Primer for the ACE...
Protega Viterlac ACV Quick Drying Alkyd Gloss Finish New Protega Viterlac ACV Quick...
Protega Viterlac ACV 90 A fast drying modified alkyd gloss...
Protega ViterLac ABV  High Build Gloss Finish New Protega ViterLac ABV High...
A high performance, modified alkyd, high gloss finish which...
Protega ViterLac AM112 Urethane Alkyd Micaceous Iron Oxide New Protega ViterLac AM112...
ViterLac AM112 - Urethane Alkyd MIO A single pack, white...
Protega ViterShield SPF New Protega ViterShield SPF
ViterShield SPF Epoxy Primer/Finish A two pack epoxy...
ProtegaLac PU90 PU modified  High Gloss Enamel New ProtegaLac PU90 PU modified...
ViterLac PU90 Gloss Finish A general purpose urethane alkyd...
ProtegaLac TF95  High Gloss CV Enamel New ProtegaLac TF95 High Gloss...
 A single pack, full gloss, high quality finish specially...