Protega ViterPrime 035 High Build Zinc Phosphate Primer/Finish Maximize

Protega ViterPrime 035 High Build Zinc Phosphate Primer/Finish

Single Pack, Quick Drying High Build Zinc Phosphate Primer for airless spray application to blast cleaned structural steelwork.

 

More details

£ 4.60

A Single Pack, Quick Drying High Build Zinc Phosphate Primer for airless spray application to blast cleaned structural steelwork.

Excellent build properties and hold-up on edges

Can be overcoated with ViterThane PLV and PLS two pack polyurethane finishes

Readily available in a wide range of Colour including BS and RAL 

Can be used as a base coat for most thin film intumescent coatings

Surface Preparation  

All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams .

Blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50-75 microns Mixing Must be mixed thoroughly by using a mechanical agitator before use. Agitate periodically to ensure paint remains homogeneous.

Thinner -1006 Thinner

Equipment Cleaner - 1006 Thinner

 

Application Conditions

Only apply in conditions of good ventilation which must be maintained during drying and curing. Do not apply when rain, mist, sleet or snow are imminent. During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3oC above the dew point. Paint temperature should ideally be at a minimum of 15ºC.

 

Application Methods

Method , Airless Spray ,  Brush or Roller

 Airless Spray: Output fluid pressure at tip 2000-2500 psi, Tip Size 17-19 thou (0.43-0.48 mm)  Thinning of the coating is not recommended as this will reduce the build qualities

Application by brush/roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work.

 

Product Notes

Overcoating

 May be overcoated with itself or other products from the ViterLac, ViterChlor or ViterThane range When the primer has been applied to 75 microns DFT, allow a minimum of 4 hours at 23ºC before overcoating with ViterLac intermediates/finishes or ViterThane PLS/PLV.

 

Allow longer intervals if applying at lower temperatures and higher film builds  

The compatibility and suitability of overcoating should be confirmed prior to application.

 

Exposure

In common with most alkyd primers, this product is not recommended for extended exterior exposure, exposure in aggressive or coastal locations, or for immersion.

 

Epoxy primers are preferred for these conditions, please call us for advice.

Some shades may contain lead based colourants and these are labelled (L).

Health & Safety Containers are provided with safety labels which should be observed.

Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets.

A Safety Data Sheet for this product is available on request .

We can tint this product to your exact specification from any colour chart or sample.

Simply select 'Tinted to your colour' from the dropdown list, enter the reference code for the colour you want in the field below, click SAVE and then add the product to your basket.

We also have ideas to set the ball rolling in our Colour Section where we have added a number of widely used colour ranges.

Need help? Call us on 01793 511537

Remember to add the product to your basket after you have saved it!

No customer comments for the moment.

Write your review

Protega ViterPrime 035 High Build Zinc Phosphate Primer/Finish

Protega ViterPrime 035 High Build Zinc Phosphate Primer/Finish

Single Pack, Quick Drying High Build Zinc Phosphate Primer for airless spray application to blast cleaned structural steelwork.

 

Write your review

Related products

RustOleum Metal Cladding Primer RustOleum Metal Cladding...
Don’t replace old and weathered cladding, Renovate with the...
Teamac Marine Undercoat Teamac Marine Undercoat
Teamac Marine Undercoat is an interior and exterior, oil based...
Teamac Marine Gloss Teamac Marine Gloss
Teamac Marine Gloss is a high quality, modified alkyd marine...
Teamac Tropical Killa Antifouling Teamac Tropical Killa...
Teamac Protector Antifouling contains cuprous oxide to give...
Teamac Protector Antifoul II Teamac Protector Antifoul II
Teamac Protector Antifouling contains cuprous oxide to give...
Teamac Antifouling D Teamac Antifouling D
Teamac Antifouling ‘D’ is a  physically ablative product and...
Teamac Antifouling A Teamac Antifouling A
Teamac "A" Antifouling is a premium physically ablative...
Teamac Boot Topping Teamac Boot Topping
5A high quality, hard wearing boot-topping paint. Used to...
Teamac Anti-Slip Suregrip Deck paint Teamac Anti-Slip Suregrip...
Teamac Suregrip provides an anti-slip finish for wood, grp and...
Teamac Bilge Paint Teamac Bilge Paint
Teamac Bilge Paint provides protection for the inside surfaces...
RustOleum Combicolor RustOleum Combicolor
A high performance, one coat interior and exterior maintenance...
Rustoleum Pegakote Rustoleum Pegakote
A waterborne, high performance satin gloss floor coating with...
RustOleum Flexible  Epoxy B95 RustOleum Flexible Epoxy B95
 Outstanding corrosion protection in heavy industrial or...
SteelSeal Metal Cladding Maintenance Paint SteelSeal Metal Cladding...
SteelSeal Metal Cladding Maintenace Paint  Akzo Nobel's...
SteelSeal Metal Cladding Maintenance Primer SteelSeal Metal Cladding...
SteelSeal Metal Cladding Maintenace Primer Akzo Nobel's...
Protega ViterPrime 016 Single Pack Zinc Phosphate Primer Protega ViterPrime 016...
 An easy to use alkyd zinc phosphate anticorrosive primer, for...
Protega ViterLac 305 Vinyl Acrylic Anti-Corrosive Primer/finish Protega ViterLac 305 Vinyl...
A high performance single pack Vinyl Acrylic Anti-Corrosive...
Protega ViterLac OCF Anti-corrosive Gloss Primer/Finish Protega ViterLac OCF...
A single pack one coat Anti-Corrosive One Coat Full Gloss...
Protega ViterLac 046 Anti-corrosive Semi-Gloss Primer/Finish Protega ViterLac 046...
A fast drying one coat, semi-gloss, anticorrosive...
Protega ViterLac C12  Anti-Corrosive Primer/Finish for Containers Protega ViterLac C12...
 A single pack, phenolic-modified alkyd primer/finish,...
Protega ViterLac Containergard HS Protega ViterLac...
A single pack Modified Anti-Corrosive One Coat Full Primer /...
Protega Prime VRP Compliant Primer for Vehicle Refinishing Protega Prime VRP Compliant...
A single pack, fast drying alkyd primer specially designed for...
ProtegaPrime QD Matt Primer ProtegaPrime QD Matt Primer
A single pack Modified Anti-Corrosive Matt Primer for the ACE...
Protega Viterlac ACV Quick Drying Alkyd Gloss Finish Protega Viterlac ACV Quick...
Protega Viterlac ACV 90 A fast drying modified alkyd gloss...
Protega ViterLac ABV  High Build Gloss Finish Protega ViterLac ABV High...
A high performance, modified alkyd, high gloss finish which...
Protega ViterLac AM112 Urethane Alkyd Micaceous Iron Oxide Protega ViterLac AM112...
ViterLac AM112 - Urethane Alkyd MIO A single pack, white...
Protega ViterShield SPF Epoxy Primer/Finish Protega ViterShield SPF...
ViterShield SPF Epoxy Primer/Finish A two pack epoxy...
ProtegaLac PU90 PU modified  High Gloss Enamel ProtegaLac PU90 PU modified...
ViterLac PU90 Gloss Finish A general purpose urethane alkyd...
ProtegaLac TF95  High Gloss CV Enamel ProtegaLac TF95 High Gloss...
 A single pack, full gloss, high quality finish specially...
Protega ViterShield 177 Protega ViterShield 177
ViterShield 177 Epoxy Primer/Finish An economical, high...