Temafloor P 300 Maximize

12.5L, Tikkurila Temafloor P 300 solvent free epoxy floor coating

A two pack, solvent free self levelling epoxy coating.

Withstands water, grease, chemicals and diluted solutions of non oxidising acids and bleaching chemicals. Also withstands 70C dry heat and 60C in immersion.

Full Gloss finish

More details

£ 150.66

 For new and old concrete floors exposed to heavy mechanical and chemical stress in industrial and storage facilities, repair shops; e.g. process or paper machine units and corridors. 

Application conditions

The relative humidity of the concrete should not exceed 97%. The temperature of the ambient air, surface or coating should not fall below + 15ºC during application or drying. Relative humidity of air should not exceed 80%.

Please note; There is a natural tendency of epoxy coatings to chalk and discolour on exterior exposure.

Preparation

New concrete
Remove laitance by power grinding, vacuum grit blasting or hydrochloric acid etching. Choose the method best suited for the premises. After grinding remove dust carefully with a vacuum cleaner. Hydrochloric acid etching is carried out with diluted hydrochloric acid
(1 part concentrated hydrochloric acid, 4 parts water). Rinse with plenty of water. Dry the floor.

Old concrete
Remove all grease, oil, chemicals and other impurities by MAALIPESU detergent. Remove old peeling paint layer by grinding or vacuum grit blasting. Choose the method best suited for the premises. Clean out pot-holes removing all loose friable material. Open cracks with e.g. an abrasive tool. Remove loose material and dust.

Cementitious levelling screed
Check compatibility with the levelling screed manufacturer.
Priming Prime using 30–50% with Thinner 1029 (or 1031) thinned Temafloor 200 Primer or 400 epoxy varnish. Pour the varnish mixture onto the floor and apply as much as is needed to impregnate the concrete surface. If necessary, repeat priming to get a non-porous surface. Subsequent treatment can be carried out after 2 hours using "wet-on-wet" technique. A porous priming coat will result in holes and air bubbles in the finished screed.
Patching Patch pot-holes and cracks with Colofill putty or a mixture of unthinned Temafloor 200 Primer epoxy varnish or Temafloor P 300 epoxy coating and dry, clean sand. Mixing ratio e.g. 1 part by volume of epoxy mixture and 1–2 parts by volume of sand of grain size 0.1–0.6 mm. Grind the patched areas before over coating.
Diluting Do not thin Temafloor P 300 epoxy coating.
Coating Over coating may be carried out with unthinned Temafloor P300 not earlier than 6 hrs and not later than 24 hrs after priming and patching. If the primed surface is not over coated within 24 hrs, it should be abraded. Pour the coating mixture onto the floor and spread it with a serrated steel trowel or a trowel. Level with a roller.

Recommended film thickness is 0.3–0.5 mm.
Mixing of components

Mix the correct proportions of base and hardener thoroughly (approx. 2 minutes) by using a low speed hand drill with a paddle. The amount of mixture depends on the area to be coated and on the pot life of the mixture. Insufficient mixing or incorrect mixing ratio will result in uneven drying of the surface, weaken the properties of the coating and risk the success of the application.
Cleaning of tools Thinner 006 1029 or Thinner 006 1031.

We can tint this product to your exact specification from any colour chart or sample.

Simply select 'Tinted to your colour' from the dropdown list, enter the reference code for the colour you want in the field below, click SAVE and then add the product to your basket.

We also have ideas to set the ball rolling in our Colour Section where we have added a number of widely used colour ranges.

Need help? Call us on 01793 511537

Remember to add the product to your basket after you have saved it!

No customer comments for the moment.

Write your review

12.5L, Tikkurila Temafloor P 300 solvent free epoxy floor coating

12.5L, Tikkurila Temafloor P 300 solvent free epoxy floor coating

A two pack, solvent free self levelling epoxy coating.

Withstands water, grease, chemicals and diluted solutions of non oxidising acids and bleaching chemicals. Also withstands 70C dry heat and 60C in immersion.

Full Gloss finish

Write your review

Related products

10L, Tikkurila Fontecryl SC 50 10L, Tikkurila Fontecryl SC 50
A waterborne, single pack fast drying alkyd modified acrylic...
10L, Tikkurila Fontecryl 10/25/50 10L, Tikkurila Fontecryl...
A waterborne, single pack fast drying acrylic based paint...
20L, Tikkurila Fontecryl AP Fast Dry Primer 20L, Tikkurila Fontecryl AP...
A waterborne, single pack fast drying acrylic based...
20L,Tikkurila Fontecryl PP Primer for Powder Coating 20L,Tikkurila Fontecryl PP...
A waterborne, single pack fast drying acrylic based primer...
10L, Tikkurila Fontedur HB 80 waterborne polyurethane topcoat 10L, Tikkurila Fontedur HB...
A durable, easy to clean two pack, waterborne polyurethane...
Fontemal Fontemal
A waterborne heat resistant silicone paint.
10L, Tikkurila Fontezinc 85, zinc rich epoxy paint 10L, Tikkurila Fontezinc...
A two pack, waterborne zinc rich epoxy paint providing...
20L, Tikkurila Temablast EV 110 20L, Tikkurila Temablast EV...
Two pack, iron oxide pigmented epoxy shop primer. Protects...
Two Pack Anti Graffiti Polyurethane Finish Two Pack Anti Graffiti...
A high opacity two pack polyurethane that has anti grafitti...
Low Smoke Two Pack Polyurethane Finish Low Smoke Two Pack...
A high opacity two pack polyurethane with excellent weather...
Tikkurila Temafloor 400 Solvent Free Epoxy Floor Sealer Tikkurila Temafloor 400...
A two pack solvent free epoxy varnish. It is used as a binder...
20L, Tikkurila Temafloor 25 Clear Polyurethane Primer for Concrete 20L, Tikkurila Temafloor 25...
A high performance single pack, moisture curing polyurethane...
Tikkurila Temafloor 210 Tikkurila Temafloor 210
A two pack solvent free epoxy varnish for use with Temafloor...
15L, Tikkurila Temafloor 200 Primer 15L, Tikkurila Temafloor...
A two pack solvent free clear epoxy primer sealer for binding...
10L, Tikkurila Fontedur FL Matt Clear Lacquer for Concrete Floors 10L, Tikkurila Fontedur FL...
A full matt, two-component waterborne polyurethane top...
10L, Tikkurila Ensi Urethane Oil 10L, Tikkurila Ensi...
A clear urethane oil for the protection and dust-binding of...
10L, Tikkurila Fontecoat FL100 Floor Coating 10L, Tikkurila Fontecoat...
A two pack water borne epoxy paint for new, old and earlier...
15L, Tikkurila Temafloor Polyurethane Floor Coating 15L, Tikkurila Temafloor...
A solvent free, two-component self levelling polyurethane...
10L, Tikkurila Temafloor 150 10L, Tikkurila Temafloor 150
A two pack solvent free epoxy paint for new and old concrete...
6L, Tikkurila Temazinc EE 6L, Tikkurila Temazinc EE
A single pack zinc dust paint offering cathodic protection for...
8L, Tikkurila Temazinc 99 two component, polyamide zinc rich epoxy paint 8L, Tikkurila Temazinc 99...
A two pack, polyamide cured zinc epoxy paint formulated to...
10L, Tikkurila Temathane PC 50/80 High Solids Polyurethane 10L, Tikkurila Temathane PC...
A semi gloss and gloss, high-solids, ultra durable two pack...
5L, Tikkurila Temabond ST 200 5L, Tikkurila Temabond ST 200
A two pack low solvent, high-solids, aluminium pigmented...
8L, Tikkurila Temabond WG 200 Low Temperature Curing, High Solids Epoxy 8L, Tikkurila Temabond WG...
A two pack, low temperature curing, aluminium pigmented...
20L, Tikkurila Temabond ST 300 20L, Tikkurila Temabond ST 300
A two pack high-solids, modified epoxy paint with high...
20L, Tikkurila Temabond WG 300 Modified Epoxy 20L, Tikkurila Temabond WG...
A two pack, low temperature curing modified epoxy paint with...
20L, Tikkurila Temachlor 40 Chlorinated Rubber Paint 20L, Tikkurila Temachlor 40...
A single pack high build paint, based on chlorinated rubber....
20L, Tikkurila Temacoat GF Primer 20L, Tikkurila Temacoat GF...
A two pack, polyamide cured epoxy primer containing zinc...
10L, Tikkurila Temathane 50/90 Two Pack Polyurethane 10L, Tikkurila Temathane...
A two pack, semi gloss and gloss polyurethane paint with...
Tikkurila Temacoat GPL Two Pack Epoxy Finish Tikkurila Temacoat GPL Two...
A two pack, Gloss amine adduct cured epoxy finish. Ideal for...